Pipe Repair in Pleasanton, TX — All Pipe Materials, Same-Visit Repairs
Pipe failures range from a slow pinhole leak weeping inside a wall to a full main line rupture. Locating the failure precisely — before opening drywall or digging — is the skill that separates a clean, affordable repair from an expensive and destructive guessing operation. Masters Plumbing Service's pipe technicians in Pleasanton, TX use acoustic listening devices and thermal imaging cameras to find the leak first, then open only what needs to be opened.
What Separates Precision Pipe Repair from Guesswork
Our techs work on every pipe material found in Pleasanton, TX homes, from pre-1970s galvanized to modern PEX-A crosslinked systems. The repair method matches the pipe.
🔊
Acoustic Leak Detection
Acoustic detection is most effective on pressurized supply lines. Combined with a pressure test to confirm water loss before we start, it tells us both that there's a leak and exactly where it is.
🌡️
Thermal Camera Scanning
Active water leaks create temperature differentials on wall and floor surfaces detectable with an infrared camera. A slow leak inside a wall shows as a cold, spreading zone; a hot water line leak shows the inverse. Thermal imaging confirms leak presence and approximate location before any cutting begins.
🛠️
All Pipe Materials & Joining Methods
Our techs are proficient in copper sweating (soldering), press-fit connections (ProPress system), CPVC solvent welding, PEX crimp and expansion fitting installation, threaded galvanized repair, and ABS/PVC drain line work. We match the repair method and material to the existing pipe system rather than forcing incompatible transitions.
🔒
Pressure-Tested Before We Leave
Every supply line repair is pressure-tested before we close the wall or floor. We pressurize the repaired section, hold the test pressure for the required duration, and confirm zero drop before considering the repair complete. You don't find out there's a second leak next week — we find it before we pack up.
Our Pipe Repair Services
What We Fix — Pipe by Pipe, Material by Material
From a pinhole copper leak behind a kitchen cabinet to a full galvanized repiping, our pipe crew in Pleasanton, TX handles the full range.
Copper
Copper Pipe Repair & Repipe
Pitting corrosion in copper is sometimes systemic rather than localized — a single pinhole is often the first of several to appear. When the camera or pressure test finds multiple deteriorated sections, we give you an honest assessment of whether targeted repair or full copper repipe is the better long-term answer.
Galvanized
Galvanized Pipe Replacement
Galvanized steel pipe was standard in homes built before the 1960s. It corrodes from the inside out — zinc coating depletes, iron oxide (rust) accumulates on the inner wall, progressively narrowing flow and leaching into the water supply. Repairs on severely corroded galvanized are generally temporary; the pipe is failing systemically along its full run.
PEX
PEX Pipe Repair & Extension
Cross-linked polyethylene (PEX) is the current standard for residential supply piping. Failures are uncommon but occur at crimp or clamp fittings that were improperly installed, at pipe runs exposed to UV degradation, or at locations where the pipe was kinked during installation. We repair using expansion fittings (for PEX-A) or crimp fittings with the correct ring size for the pipe diameter.
Burst Pipes
Burst & Freeze-Damaged Pipe Repair
We also inspect upstream of the burst for additional sections that froze but haven't yet failed — because a partially-thawed line sometimes shows multiple failure points only after pressure is restored.
Slab Leaks
Under-Slab Pipe Leak Repair
Supply line leaks under a concrete slab are identified by acoustic detection and confirmed by thermal imaging. Once located, we evaluate three repair options: direct-access repair (jackhammering to the pipe, repairing the section, and patching the slab); rerouting the line through the wall framing above slab to bypass the failed underground run; or epoxy pipe lining for older copper systems with systemic pinhole corrosion.
Full Repipe
Whole-House Repipe Service
A full repipe in Pleasanton typically completes in 2–3 days for a standard single-family home. You're without water for a portion of each day; we plan the schedule to minimize disruption to occupied rooms.
Here's how a Masters Plumbing Service pipe repair call plays out in Pleasanton, TX.
1
Call & Describe — We Shut the Water If Needed
Active leak? Our dispatcher walks you through shutting off the main supply valve while we drive to you. Describing what you see — water stain on a ceiling, drop in water pressure, wet flooring — helps us arrive with the right detection tools loaded.
2
Pressure Test & Acoustic / Thermal Detection
This detection step routinely saves homeowners $500–$2,000 in unnecessary drywall removal compared to opening walls speculatively.
3
Flat-Rate Quote & Minimal Access Opening
You receive a flat-rate quote covering the specific repair based on what the detection confirmed. We open only what needs to be opened — typically a 12–18 inch drywall or flooring access, not a full wall section.
4
Repair & Pressure Test — Then You're Done
You receive a written summary of what failed, what we installed, and the warranty terms before we leave.
Customer Reviews
Masters Plumbing Service Pipe Repair — How We Handle It
★★★★★
My older home had a copper supply line fail inside an exterior wall. The thermal camera showed the wet zone through the drywall without any cutting. They opened a 10-inch section right at the pinhole, put in a press-fit repair coupling — no torch in my wall — pressure tested, and patched the drywall themselves. Two hours total.
— N. Bergman, Pleasanton
★★★★★
Had an under-slab leak diagnosed by Masters Plumbing Service with acoustic equipment. They found the leak at 6 feet from the wall — a single copper elbow that had developed a pinhole. Presented three options: direct slab access, reroute through the wall framing above, or copper lining. I chose the reroute — they ran a new PEX line through the crawl space and connected at both ends without touching the slab. Pressure tested, verified no remaining drop. No jackhammering at all.
— O. & R. Adeyemi, Pleasanton, TX
★★★★★
Pipe burst in a rental property at 2 AM — Masters Plumbing Service's emergency line answered immediately, talked my tenant through the main shutoff, and had a tech there in 45 minutes. Freeze crack in a PEX line in an exterior wall. Repair and insulation wrap done in under two hours. Detailed receipt for insurance documentation. Exactly what I needed as a landlord dealing with a crisis remotely.
— F. Okoro, Pleasanton, TX
Common Questions
Pipe Repair Questions We Answer Every Day
A slow pinhole leak inside a wall can run for months before surface damage appears. By the time you see a stain, the moisture intrusion is typically already significant. If your meter shows movement with everything off, call us — we can pressure-test and locate it before it becomes a major remediation project.
In most cases, the pipe itself needs to be physically accessed to make a durable repair — but the amount of wall we open depends entirely on how precisely we can locate the failure first. With acoustic detection and thermal imaging, we typically open a single, small access point rather than a wide section of wall.
A slab leak is a supply line or drain line failure in a pipe that runs through or under the concrete foundation slab. Supply line slab leaks are the more urgent scenario — pressurized water escaping under the slab saturates the subgrade, can undermine the foundation, and drives significant water bills.
We assess galvanized condition when we're on-site — visible exterior corrosion, interior scale visible at the cut failure point, and water pressure readings all tell us how advanced the system deterioration is. We give you the repair-vs-repipe math honestly so you can make the decision that fits your timeline and budget.
We don't rush pressure testing at the end. That's the step that confirms the repair is actually complete, and it takes the time it takes.
For slab access openings, we clean up concrete debris, complete the pipe repair, and patch the concrete. Tile or flooring restoration over a slab patch is normally a separate trade.
Service Area
Pipe Repair Covering Pleasanton and All of Pleasanton, TX
Masters Plumbing Service dispatches pipe repair technicians throughout Pleasanton and the broader Pleasanton, TX service area. Same-day service is available on most calls. Emergency burst pipe response is available 24 hours a day.
Burst or Leaking Pipe? Call +1-855-718-1500 Right Now
Active pipe leaks compound fast — mold growth can begin in 24–48 hours of sustained moisture. Masters Plumbing Service's pipe repair crew is in Pleasanton today, equipped with acoustic and thermal detection tools to find the failure precisely before anything is opened.
